Flashing, Chimney & Skylight Repair in Shreveport, LA

Flashing, Chimney & Skylight Repair in Shreveport is the work that stops the leaks most local roofs actually get, and it is the repair we get called for more than any other. Shreveport sits on the Red River in the Ark-La-Tex, on red clay and sandy loam, under tall loblolly pines, live oaks, magnolias, sweetgums and crape myrtles that drop limbs and needles straight onto roofs. The housing stock runs from 1890s-1920s Queen Anne and Craftsman homes with deep porches in Highland and South Highlands, through 1920s-50s brick Colonials in Broadmoor and Southern Hills, to 1990s-2020s subdivision homes around Cross Lake, Benton and Blanchard. Every one of those roofs has seams, penetrations and wall junctions where water finds a way in. We bend and fit flashing in-house so it matches the panel profile and the brick line, instead of forcing a generic piece to fit. If you are already chasing a leak, start with our metal roof leak repair page and we will trace it to the source.

Why Flashing and Chimney Leaks Dominate Shreveport Roofs

Long, hot, humid summers feed algae and mildew on north-facing slopes, and spring supercell thunderstorms throw large hail and tornadoes across Caddo and Bossier Parishes. Tropical-storm remnants dump heavy rain in short bursts, and the occasional ice storm coats trees and roofs. That cycle of heat, UV and driven rain is hard on sealant and on the thin metal collars around pipes and skylights. On the older homes in Highland and Queensborough, the chimney flashing is often original and has been patched with tar more than once.

• Chimney flashing pulls away from brick as mortar and counter-flashing age, letting water run behind the step flashing.
• Skylight curbs on 1980s and 1990s homes around Cross Lake crack at the seal and leak at the curb, not the glass.
• Valley flashing on dormers and complex rooflines collects pine needles and backs water up under the panels.
• Wall and headwall flashing on brick veneer fails where the original builder relied on caulk instead of a reglet.
• Pipe boots and vent collars dry out and split within a few summers of UV exposure.

Almost every one of these is a metal problem, and metal is what we fabricate and install.

Key info: On a 1920s brick Tudor in Broadmoor, we pulled three layers of roof cement off a chimney and found the original step flashing had rusted through at the bend. New 24-gauge bent counter-flashing and a proper reglet cut into the mortar closed a leak that had stained the ceiling for two seasons.

Roofing permits and inspection requirements vary by jurisdiction across Shreveport and Bossier City, so confirm the current rules with the local building department before work starts. The City of Shreveport's permits office publishes its requirements online at shreveportla.gov.

How We Repair Flashing, Chimneys and Skylights on Shreveport Roofs

We start by finding the actual entry point, not the stain. Water travels along framing, so a ceiling mark in Southern Hills can trace back to a chimney two rooms away. We get on the roof, open the suspect junction, and photograph what we find so you see the same thing we do. Then we fabricate the piece on site to fit the panel, the curb or the brick.

1. We inspect the roof, attic and all penetrations, and we mark the true source of the leak.
2. We remove failed sealant, old tar patches and rusted flashing down to sound material.
3. We cut a reglet or set a proper counter-flashing where the roof meets brick or siding.
4. We bend new flashing from 24-gauge or copper stock to match the panel profile and color.
5. We set step flashing, apron and headwall pieces in the correct shingle or panel sequence.
6. We seal, fasten and water-test the repair, then clean the gutters of the debris we loosened.

Every repair ends with a water test and a walkthrough, so you know exactly what was fixed and why it failed.

Key info: A homeowner in Haughton had paid twice for skylight resealing. The curb itself had rotted under the old seal. We rebuilt the curb, bent a new copper cap and collar, and the leak stopped because we fixed the structure, not the caulk line. Homeowners in the 71101 and 71110 zips can see local details on our Shreveport 71101 page.

Repair Approaches We Use on Shreveport Metal Roofs

Not every leak calls for the same fix. The right approach depends on the roof material, the age of the flashing and how the original roof was detailed. Here is how we match the method to the job.

We choose the method after we see the junction, not before, because the wrong fix just moves the leak a few feet.

Flashing, Chimney & Skylight Repair Cost in Shreveport: What to Expect

Small flashing repairs in Shreveport generally start at From $600, which covers the trip, the roof inspection, the removal of failed sealant and a straightforward replacement at one penetration. From there, the price moves with the scope: a single pipe boot is at the low end, while a full chimney re-flash with a reglet cut into brick, or a skylight curb rebuild, lands well above it. Access matters too. A steep two-story roof in South Highlands takes more setup than a single-story ranch in Blanchard.

• The number of penetrations and junctions involved drives the total, since each one needs its own fabricated piece.
• Brick and masonry work costs more than panel work because the reglet has to be cut cleanly.
• Rotted curb or decking found under the old flashing adds carpentry time to the job.
• Copper or color-matched stock costs more than standard 24-gauge galvanized.
• Emergency tarping and after-hours response carry a higher rate than scheduled work.

Getting two or three written estimates is smart, because flashing scope varies widely and a low bid often leaves the hidden junction untouched. Our full pricing overview breaks down how we build a number.

Flashing, Chimney & Skylight Repair Near Me: How to Pick a Contractor in Shreveport

When you search for flashing repair near me in Shreveport, the list looks long, but the good ones share a few traits. Start with licensed and insured status and ask for the certificate, not just a verbal yes. Get at least two written estimates that describe the flashing method, not just a price. Ask for local references on homes like yours, and ask who pulls the permit if one is required. If your home sits in a historic district or an HOA, confirm the design review rules before anyone orders metal.

• Confirm the contractor carries general liability and workers' compensation coverage and can show proof.
• Ask whether they fabricate flashing in-house or buy stock pieces that may not fit your profile.
• Request references from jobs in your part of town, whether that is Broadmoor, Benton or Mooringsport.
• Ask who handles the permit and the inspection if the local building department requires one.
• Get the scope, the material gauge and the warranty in writing before work begins.

Reach us through our contact page or call (318) 666-5827 to set up an inspection.

Flashing, Chimney & Skylight Repair in Shreveport: Pricing Guide

Indicative pricing, the exact cost depends on square footage, finish, and site access. Free personalized estimate within 24h at (318) 666-5827.